*

*     Aruba     APIN0535

*       S/N : CNL5K9W11H

*

*       Factory reset

*       Login ID : admin

*       Password : CNL5K9W11H

*

 

APBoot 2.5.3.10 (build 74666)

Built: 2020-03-12 at 17:05:54

Model: AP-53x/555

DRAM:  2 GiB

Flash: Detected MX25U6435F: total 8 MiB

NAND:  256 MiB

Power: 802.3af POE, port0

       No POE, port1

Net:   PHY8 - Loading firmware ................ done

       PHY7 - Loading firmware ................ done

       eth0

Radio: ipq8074#0, ipq8074#1

Reset: cold

FIPS:  passed

Hit <Enter> to stop autoboot:  0

apboot>

apboot>

apboot>

apboot> purgeenv

preserving os_partition (0)

Erasing SPI flash...Writing to SPI flash...done

Erasing SPI flash...Writing to SPI flash...done

apboot>

apboot>

apboot> factory_reset

Clearing state...

Checking OS image and flags

Invalid image format version: 0xffffffff

Clearing image partition 0

512 bytes written to volume aos0

Erasing UBIFS ...done

Purging environment...

preserving os_partition (0)

Erasing SPI flash...Writing to SPI flash...done

Erasing SPI flash...Writing to SPI flash...done

apboot>

apboot>

apboot> boot

Booting OS partition 0

Checking image @ 0x0

Invalid image format version: 0xffffffff

Checking image @ 0x3000000

Copying image from 0x50500000

Image is signed; verifying checksum... passed

SHA2 Signature available

Signer Cert OK

Policy Cert OK

RSA signature verified using SHA2.

Uncompressing Kernel Image ... OK

[    0.000000]

[    0.000000] Aruba Networks

[    0.000000] ArubaOS Version 8.6.0.2-8.6.0.2 (build 73853 / label #73853)

[    0.000000] Built by p4build@pr-hpn-build09 on 2020-01-09 at 08:29:55 UTC (gcc version 5.3.0)

[    0.000000] p:anul_base: 0xb9c00000, v:anul_base: 0xffffffc079c00000, size:0x1800000

[    5.396357] tpm tpm0: TPM2_RC_INITIALIZE (256) continue selftest

[    6.136717] tpm tpm0: TPM2 self test passed

[    6.457334] Skip QCA8074V1 in V2 platform

[    6.673153] DEV CI test message

[    6.685229] DEV CI test message

[    8.595965] Starting Kernel SHA1 KAT ...

[    8.595986] Completed Kernel SHA1 KAT

[    8.630373] Starting Kernel HMAC-SHA1 KAT ...[    8.630437] Starting Kernel DES KAT ...

[    8.630460] Completed Kernel DES KAT

[    8.630461] Starting Kernel AES KAT ...[    8.630485] Completed Kernel AES KAT

[    8.630486] Starting Kernel AESGCM KAT ...[    8.630487] Completed Kernel AESGCM KAT

[    8.632938] Completed Kernel HMAC-SHA1 KAT

Thu Jan  1 00:00:00 PST 1970

Populate AP type info

Domain Name: SetMeUp.arubanetworks.com

Current OEM Name : Aruba Networks

Disabling ipv6 for devices by default

AP-type has_ble_support: NORDIC_ONBOARD.

IPv6 capability is supported for devices

apboot_upgrade[330]: the running APBoot is up to date

No panic info available

No panic info available

Writing /dev/ttyMSM1 into /tmp/ble_port

Enabling ble_daemon and ble_relay via nanny

kilchoman: Start hotplug

apfcutil: sector CACHE: Cache uninitialized

apfcutil: sector RAP: Cache uninitialized

apfcutil: sector FAT: Cache uninitialized

apfcutil: sector DRT: Cache uninitialized

apfcutil: sector SCRATCH: Cache uninitialized

Backup ENV.

apfcutil: sector MESH Prov: Cache uninitialized

[   16.201938] nss_driver - fw of size 656464  bytes copied to load addr: 40000000, nss_id : 0

[   16.203286] Supported Frequencies -

[   16.287397] 748.8 MHz 1.4976 GHz

[   16.359256] 1.6896 GHz [   16.371756]

[   16.398995] ffffff800094fc00: meminfo init succeed

[   16.434460] nss_driver - fw of size 293940  bytes copied to load addr: 40800000, nss_id : 1

[   16.444580] node size 2 # items 4

[   16.444584] memory: 40000000 2147483648 (avl 1887678464) items 4 active_cores 2

[   16.444588] ffffff800094fc00: nss core 0 booted successfully

[   16.699625] Supported Frequencies -

[   16.769684] 748.8 MHz 1.4976 GHz

[   16.838424] 1.6896 GHz [   16.850922]

[   16.878137] ffffff8000956f00: meminfo init succeed

[   16.903828] node size 2 # items 4

[   16.951991] memory: 40000000 2147483648 (avl 1889374208) items 4 active_cores 2

[   16.992608] ffffff8000956f00: nss core 1 booted successfully

dev.nss.general.logbuf = 2000

 SSDK Init OK!

operation done.

 SSDK Init OK!

operation done.

 SSDK Init OK!

operation done.

Enter non-FIPS mode

Cfg len is 0

Configuration file is empty, turning on default services...

extended ssid activate due to no AP config ...

The AP is in factory default status

Mesh enabled

Ethernet port 1 mode: active-standby

Info: use bonding and enslave eth1

Starting watchdog process...

Aruba watchdog daemon started [4 thread(s)]

dual_uplink_default is 0

touching file /tmp/ip_mode_0

Enable IPv6 for the Master v6 discovery

Enabling DHCPv6 ...

init usb modem ...

No USB Plugged in

Checking country code.

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

Ethernet uplink eth0 not active yet

skip backup uplink detect, as factory uap

No uplink active. Becoming Mesh Point

Factory default ap without uplink, it will become a point.

copying bootuplog ...

[   71.808783] aruba_alloc_contig_range freeing 2490 reserved pages at:0xffffffc07aa46000

allow PAPI

set device anul0 mtu to 2000

notify asap_mod 3g no present...

Starting update TZ ...

Done.

Enabling IPv6 for devices... IP mode is v4-only...

apdot1x authentication is not enabled

Starting DHCP

Compressing all files in the /etc/httpd directory...

Done.

Starting Webserver

bind: Transport endpoint is not connected

bind: Transport endpoint is not connected

bind: Transport endpoint is not connected

Put ntpdate to the nannylist.

[   84.428540] diag: IPC Logging disabled

[   84.476097] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done

Initiating cold boot calibration

[   84.844090] glink_core_link_up glink is up

[   84.844222] glink_xprt_open_event

[   84.880411] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, ffffff8000844bc8

[   84.881440] cnss: BDF download response , result: 0, err: 0x0

[   84.883914] cnss: BDF download response , result: 0, err: 0x0

[   90.650607] glink_core_link_down glink is down

[   90.650635] <SSR>: glink SUBSYS_AFTER_SHUTDOWN cleanup done

[   90.725517] glink_xprt_close_event

[   90.881698] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done

[   91.237706] glink_core_link_up glink is up

[   91.237828] glink_xprt_open_event

[   91.377320] cnss: BDF download response , result: 0, err: 0x0

[   91.379877] cnss: BDF download response , result: 0, err: 0x0

[   91.446947] __ol_ath_attach 3344: Aruba: preferred_hw_mode 7 updated to 1 (6)

[   91.652707] copy_hw_mode_in_init_cmd 6411: pdev 0 hw_mode_index 1 num_band_to_mac 2

AP rebooted caused by cold HW reset(power loss)

Dump Capture Kernel: Dump capture kernel:AP rebooted caused by cold HW reset(power loss)

shutting down watchdog process (nanny will restart it)...

        <<<<<       Welcome to the Access Point     >>>>>

Completed SW FIPS KAT test

Power supply mode is POE-AF:, UUser: ble_ready NOT present @init ....

Firmware AES-CCM Known Answer Test Passed

User: admin

Password:

Warning: CLI module is running in a degraded state.  Configuration, write memory, and support command are disabled; please debug with caution.

show tech-support and show tech-support supplemental are the two most useful outputs to collect for any kind of troubleshooting session.

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76# sh ver

Aruba Operating System Software.

ArubaOS (MODEL: 535), Version 8.6.0.2

Website: http://www.arubanetworks.com

(c) Copyright 2020 Hewlett Packard Enterprise Development LP.

Compiled on 2020-01-09 at 08:29:55 UTC (build 73853) by p4build

FIPS Mode :disabled

AP uptime is 5 minutes 45 seconds

Reboot Time and Cause: AP rebooted caused by cold HW reset(power loss)

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76# sh run

version 8.6.0.0-8.6.0

virtual-controller-key 17f4852101b1daf0ea1b390d7ece7edefaec2bcf84b465298d

name SetMeUp-C4:9A:76

clock timezone none 00 00

rf-band all

arm

 wide-bands 5ghz

 min-tx-power 18

 max-tx-power 127

 band-steering-mode prefer-5ghz

 air-time-fairness-mode default-access

syslog-level warn ap-debug

syslog-level warn network

syslog-level warn security

syslog-level warn system

syslog-level warn user

syslog-level warn user-debug

syslog-level warn wireless

auth-survivability cache-time-out 24

wlan external-captive-portal

 server localhost

 port 80

 url "/"

 auth-text "Authenticated"

blacklist-time 3600

auth-failure-blacklist-time 3600

ids

 wireless-containment none

uplink

 preemption

 enforce none

 failover-internet-pkt-lost-cnt 10

 failover-internet-pkt-send-freq 30

 failover-vpn-timeout 180

airgroup

 disable

airgroupservice airplay

 disable

 description AirPlay

airgroupservice airprint

 disable

 description AirPrint

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76#

b8:3a:5a:c4:9a:76# sh su

subscription-aps

summary

support-commands

supported-cert-formats

b8:3a:5a:c4:9a:76# sh summary support

Name                 :SetMeUp-C4:9A:76

System Location      :

Domain               :

VC IP Address        :0.0.0.0

VC IPv6 Address      :::

AP1X                 :NONE

VC VLAN              :0

VC Mask              :0.0.0.0

VC Gateway           :0.0.0.0

VC DNS               :0.0.0.0

IP Mode              :v4-only

Cluster-Security DTLS:disable

Content Filtering    :disable

Terminal Access      :disable

Telnet Server        :disable

Activate Disable     :disable

Organization         :

Disable ciphers      :

Airwave Server       :

Airwave Backup Server:

Airwave Prov Backup  :

Number of VC transition  :0

Airwave Shared Key   :

Airwave Config Via   :DHCP

Airwave              :Not Set Up

Aruba Central Server  :

Aruba Central        :Not Set Up

Managed Via          :Local

Syslog Server        :0.0.0.0

Syslog Server        :0.0.0.0

Syslog Server        :0.0.0.0

Syslog Level         :warn

Band                 :all

Master IP Address    :0.0.0.0

IP Address           :0.0.0.0

Netmask              :0.0.0.0

Gateway              :0.0.0.0

IPv6 Address         :--

Master Key           :17f4852101b1daf0ea1b390d7ece7edefaec2bcf84b465298d

Elected Time         :5m:54s

Dynamic Radius Proxy :disable

Dynamic Tacacs Proxy :disable

NTP Server           :

Configuration Dirty  :disable

Allow New APs        :disable

Classification       :disable

Containment Confirm  :disable

Wireless Containment :disable

Wired Containment    :disable

Wired Containment AP Adjacent MAC  :disable

Wired Containment Suspect L3 Rogue :disable

Rogue Containment    :disable

LED Off              :disable

AppRF Visibility     :none

URL Visibility       :disable

WebCC Visibility     :disable

Image Server State   :success

Image Server Message :Success

New Image Version    :

New Image URL        :

Factory SSID         :SetMeUp

Image Sync Via       :Master

AP Alerts            :0

Client Alerts        :0

Active Faults        :0

Fault History        :0

Usb Support          :YES

Serial Number        :CNL5K9W11H

OpenDNS Status       :Not connected

TFTP Dump Server     :0.0.0.0

Extended SSID        :disable

Mesh role detect     :disable

Inactivity-ap-timeout:60

Config Sync Status   :TRUE

VPN Status           :Not Set Up

Mobility Acccess Switch Integration :disable

Deny inter user bridging            :disable

Deny local routing                  :disable

Support Connection Status           :Not Connected

Dynamic CPU Management:auto

Restrict Corporate Access:disable

SLAAC IP Address:--

Link Local IP Address:--

0 Clients

---------

MAC  Name  IP Address  ESSID  Access Point

---  ----  ----------  -----  ------------

0 Networks

----------

Profile Name  ESSID  Clients  Status  Type

------------  -----  -------  ------  ----

0 Access Points

---------------

MAC  IP Address  Name  Clients  Need Antenna Config

---  ----------  ----  -------  -------------------

Restricted Management Access Subnets

------------------------------------

Subnet IP Address  Subnet Mask

-----------------  -----------

RADIUS Servers

--------------

Name            IP Address  Port  Key                                                                                                                               Timeout  Retry Count  NAS IP Address  NAS Identifier  RFC3576  Airgroup RFC3576-ONLY  Airgroup RFC3576 port  DRP IP  DRP Mask  DRP VLAN  DRP Gateway  RFC5997

----            ----------  ----  ---                                                                                                                               -------  -----------  --------------  --------------  -------  ---------------------  ---------------------  ------  --------  --------  -----------  -------

InternalServer  127.0.0.1   1616  04aafba9cb5d078a70827ad90938bb7ba71787ff9b481c0f6f901a3dcf9daf34ef84f5dd6b7759d2b04677d31161993ecc5453f287107c957af6e73f8f160628  5        3                                                                            0                                                               n

RTLS Servers

------------

Type       Address  Port  Key  Frequency  Include Unassociated Stations  CM

----       -------  ----  ---  ---------  -----------------------------  --

Aeroscout           0                     disable                        N/A

Airwave             0          0          disable                        enable

1 AP Class

----------

Name     APs

----     ---

Scorpio  0

Uplink type         :Wifi-mesh

Uplink status       :DOWN

OOS Hold On Time       :30

Manual Blacklist Count :0

Dyn Blacklist Count :0

Certificate Installed: :No

Internal Radius Users   :0

Internal Guest Users   :0

Internal User Open Slots   :512

Openflow Server :

Openflow Server Port:30633

Openflow Server tls-enable:False

PAN Firewall Port          :443

PAN Firewall Status        :Disabled

Auto save        :Enabled

Stats Sample Cnt :15

Stats Interval   :30

Monitor Interval   :0

Need central wizard        :No

Info timestamp      :354

Uplink switch native VLAN:0

Radius RFC3576 Listen Port   :3799

New Password :Do not change password

split 5ghz mode :disable

b8:3a:5a:c4:9a:76#